How To Upload Presets To Peavey Vip

VSX 26 Presets

Width 375 Height 60

Instructions for transfering VSX presets from the spider web to your VSX unit

Gear up your memstick. The easiest fashion is to plug a USB 2.0 memstick directly into your VSX 26'due south USB "A" slot. So press the TOOLS push button. Scroll to "Save Preset" and press the Data bicycle to select. Press the Data wheel (to select) when on "Location" and plough the Data bike clockwise until "USB Memstick" appears in the window. Just proceed to save whatever is the existing preset (it doesn't thing what it is or it'due south proper noun) . By doing so, the VSX 26 creates all the folders necessary to transfer downloaded presets to the unit itself.

Alternately you can create the binder: VSX26 and then create the folder: presets and drag it inside the VSX26 folder.

After downloading the presets you need from the website, drag them into VSX26/presets folder while the memstick is plugged into your computer.

To load the presets into the VSX 26 plug the memstick into the "A" USB slot, press the TOOLS push and plow the Data wheel until it stops on "Load Preset". Press the Data bicycle to select. While "load" is highlighted printing the Data wheel to make the cursor jump to the preset name field. Turn the Information cycle until it says USB Memstick with the name of the desired preset under it. Then printing the Data wheel again to move the cursor and plow the Information bicycle until "OK" is highlighted. Then printing the Information wheel to select, it volition ask before overwriting the current and answer "OK" again.

Instructions for installing firmware

Only install downloaded update in the folder: vsx26/firmware on your memstick. Restart the VSX pressing the Information wheel. Insert the memstick and follow the on screen instructions.

Troubleshooting: should y'all accept any problems after following the in a higher place instructions defragging your memstick unremarkably solves them. Put the stick back in your figurer and select it (drive) for defragging by whatever method you utilise on your computer. The other caution is to allow x to 15 seconds for your VSX to recognize your memstick subsequently y'all first plug it into the VSX.

Instructions for Autograph ™ for VSX 26 (v1.05)

The Autograph algorithm for VSX 26 can measure and automatically set your forepart graphic EQ's to eliminate peaks in your acoustic surround. Nosotros have designed this process to exist equally unobtrusive as possible and take eliminated the demand for lengthy pink racket sessions. Pink noise is ramped up and left active just long plenty for the VSX26 to take snapshots of the audio field. The system makes three sweeps of the sound field (each of which is a four measurement boilerplate ... total of 12 measurements) and sets the filters as needed. You can also make multiple measurements from different locations (recommended) and automatically boilerplate them together to amend smooth out the performance of your system.

i. Claw up PVR2 measuring microphone to front panel.
2. In "MIC" setup screen, make sure phantom is on and the gain is set up sufficiently loftier (kickoff around 60dB gain to make sure it picks up betoken...). Standard mic placements and measuring techniques utilise. Excessive background noise volition take a negative issue on the process and should be avoided.
three. Make sure matrix is fix the way you want to use it in the real system. You practice not demand to route the MIC anywhere... the AutographT algorithm will take care of that. 4. Outputs should be wired up to amps, which in turn should exist connected to speakers every bit in a normal setup.
v. Amps should be turned on and at to the lowest degree turned upward to moderate volume...
6. Select TOOLS->AUTOGRAPH->OK->START NEW ANALYSIS and the system will automatically ramp upwards noise signals and make measurements... 3 times on Input A then 3 on input B. If the signal does not hear sufficient level it volition kicking out.
7. A warning screen will exist displayed... "Automatically adjust Graphic EQ? ... Pink noise generated".
eight. Iii options will be displayed:

Kickoff New Analysis
Clear/reset existing GEQ settings, make assay, adjust GEQ with results
Analyze Again and Boilerplate Results
Does NOT reset existing GEQ settings and averages the analysis with existing settings. Will average as many measurements as performed.
Abolish

FIRMWARE
VSX26 Firmware - two/two/07

PRESETS
QW2-118.V26 - QW 2 with QW 118 subs, tri-amped
QW2-218.V26 - QW 2 with QW 218, tri-amped
QW2-BI.V26 - QW ii, bi-amped
QW3-218.V26 - QW 3 with QW 218, tri-amped Updated
QW3_BI.V26 - QW 3, bi-amped
QW4-218.V26 - QW 4 with QW 218, tri-amped
QW4-BI.V26 - QW 4, bi-amped
SP1G-218.V26 - SP i with SP 218, tri-amped
SP2-118.V26 - SP 2 with SP 118, tri-amped
SP2-218.V26 - SP 2 with SP 218, tri-amped
SP2-BIB.V26 - SP 2, bi-amped
SP2X-BI.V26 - SP 2X, bi-amped
SP3-118.V26 - SP iii with SP 118, tri-amped
SP3-218.V26 - SP 3 with SP 218, tri-amped
SP3-BI.V26 - SP three, bi-amped
SP4-118.V26 - SP 4 with SP 118, tri-amped
SP4-218.V26 - SP four with SP 218, tri-amped
SP4-BI.V26 - SP 4, bi-amped
SP6-218.V26 - SP half-dozen with SP 218, tri-amped
SP6-BI.V26 - SP 6, bi-amped
VR-PJT8.V26 - Versarray Project 8 organization
QWMONS.v26 - Qw monitor speakers bi-amped
Sp5Sp118.v26 - Sp5.5 powerer with SP118 subwoofer

VSX 26 Presets

FIRMWARE
VSX26 Firmware - 2/two/07

PRESETS
QW2-118.V26 - QW ii with QW 118 subs, tri-amped
QW2-218.V26 - QW 2 with QW 218, tri-amped
QW2-BI.V26 - QW 2, bi-amped
QW3-218.V26 - QW 3 with QW 218, tri-amped Updated
QW3_BI.V26 - QW three, bi-amped
QW4-218.V26 - QW 4 with QW 218, tri-amped
QW4-BI.V26 - QW 4, bi-amped
SP1G-218.V26 - SP 1 with SP 218, tri-amped
SP2-118.V26 - SP 2 with SP 118, tri-amped
SP2-218.V26 - SP 2 with SP 218, tri-amped
SP2-BIB.V26 - SP 2, bi-amped
SP2X-BI.V26 - SP 2X, bi-amped
SP3-118.V26 - SP 3 with SP 118, tri-amped
SP3-218.V26 - SP iii with SP 218, tri-amped
SP3-BI.V26 - SP iii, bi-amped
SP4-118.V26 - SP four with SP 118, tri-amped
SP4-218.V26 - SP 4 with SP 218, tri-amped
SP4-BI.V26 - SP four, bi-amped
SP6-218.V26 - SP vi with SP 218, tri-amped
SP6-BI.V26 - SP half-dozen, bi-amped
VR-PJT8.V26 - Versarray Project Eight arrangement
QWMONS.v26 - Qw monitor speakers bi-amped
Sp5Sp118.v26 - Sp5.v powerer with SP118 subwoofer

Max width 375

Instructions for transfering VSX presets from the spider web to your VSX unit

Prepare your memstick. The easiest way is to plug a USB 2.0 memstick direct into your VSX 26's USB "A" slot. Then press the TOOLS button. Coil to "Save Preset" and printing the Data wheel to select. Printing the Data wheel (to select) when on "Location" and turn the Data wheel clockwise until "USB Memstick" appears in the window. Simply proceed to salve whatever is the existing preset (it doesn't affair what it is or it's name) . Past doing and so, the VSX 26 creates all the folders necessary to transfer downloaded presets to the unit itself.

Alternately you lot can create the binder: VSX26 and and then create the folder: presets and drag it inside the VSX26 folder.

After downloading the presets yous need from the website, elevate them into VSX26/presets folder while the memstick is plugged into your reckoner.

To load the presets into the VSX 26 plug the memstick into the "A" USB slot, printing the TOOLS button and turn the Data bike until it stops on "Load Preset". Press the Information bike to select. While "load" is highlighted press the Information wheel to make the cursor jump to the preset proper noun field. Turn the Data cycle until it says USB Memstick with the name of the desired preset under it. Then press the Data wheel once more to move the cursor and plough the Data bike until "OK" is highlighted. Then press the Data bike to select, it will ask before overwriting the current and answer "OK" once more.

Instructions for installing firmware

Just install downloaded update in the folder: vsx26/firmware on your memstick. Restart the VSX pressing the Data cycle. Insert the memstick and follow the on screen instructions.

Troubleshooting: should you have any problems subsequently following the in a higher place instructions defragging your memstick usually solves them. Put the stick back in your computer and select it (drive) for defragging by any method yous use on your calculator. The other caution is to allow 10 to xv seconds for your VSX to recognize your memstick after you first plug it into the VSX.

Instructions for Autograph ™ for VSX 26 (v1.05)

The Autograph algorithm for VSX 26 tin measure and automatically set your front cease graphic EQ's to eliminate peaks in your audio-visual environment. We take designed this process to exist as unobtrusive as possible and take eliminated the need for lengthy pink noise sessions. Pinkish noise is ramped up and left active only long enough for the VSX26 to take snapshots of the sound field. The arrangement makes 3 sweeps of the sound field (each of which is a iv measurement average ... total of 12 measurements) and sets the filters as needed. You can also make multiple measurements from different locations (recommended) and automatically average them together to ameliorate smooth out the performance of your organization.

one. Hook upwards PVR2 measuring microphone to front end panel.
two. In "MIC" setup screen, make sure phantom is on and the proceeds is ready sufficiently high (showtime around 60dB gain to make sure it picks upwardly signal...). Standard mic placements and measuring techniques apply. Excessive groundwork dissonance will have a negative effect on the process and should be avoided.
3. Make certain matrix is set the way you want to use information technology in the real system. You do not need to route the MIC anywhere... the AutographT algorithm will accept care of that. four. Outputs should be wired up to amps, which in turn should be connected to speakers as in a normal setup.
v. Amps should be turned on and at least turned up to moderate volume...
6. Select TOOLS->AUTOGRAPH->OK->START NEW Assay and the system will automatically ramp up dissonance signals and make measurements... 3 times on Input A then 3 on input B. If the signal does not hear sufficient level it will kick out.
7. A alarm screen will be displayed... "Automatically adapt Graphic EQ? ... Pinkish noise generated".
8. 3 options will be displayed:

Offset New Assay
Articulate/reset existing GEQ settings, make analysis, conform GEQ with results
Clarify Once more and Average Results
Does Non reset existing GEQ settings and averages the analysis with existing settings. Will average equally many measurements as performed.
Abolish